The Brophy Camper Scissor Steps # SS02 does come with the mounting bracket to attach to your RV as well as the necessary hardware. I've added a link to a video review of these steps for you to take a look at. view full answer...
The TorkLift GlowStep Camper Scissor Steps # TLA7803-8000 have a horizontal bar above the top step that is the mounting bracket to connect the steps to an RV. I've linked the install details that show how it's installed.
There are also two vertical bars on the bottom step that re the including landing gear.
There's also an optional GlowGuide Handrail # TLA7621 that many people like to include with the GlowStep. view full answer...
For a Furrion AC kit that comes with everything needed to add AC to your cargo trailer/camper you'd want the part # FR55PV which comes with all of the wiring needed, the single zone controller, the thermostat, and the distribution vent that would mount on underside of your roof hole. view full answer...
I confirmed with MORryde that the bolt that you need to fit into the floor-mounting hole of the MORryde RV Cargo Sliding Tray - 72" x 29" - 2 Way Slide - 80 Percent Extension # MR49FR is a 5/16" bolt. This bolt is included in the hardware kit that comes with the # MR49FR. view full answer...
The Solera 18' Solid Black RV Awning Roller and Fabric (Std) # LCV000211506 is not the complete assembly, just the roller and fabric.
We do not have any installation videos on your 2020 Merceds-Benz Sprinter, however, if you need a complete kit with everything needed for installation, we have # LCV000334961-362243, in black fade, or # LCV000334998-362241 in white fade. view full answer...
The Global Link RV Entry Door Locking Latch Kit part # 295-000019 does come with installation hardware which consists of four screws. There will be two screws that hold the face of the latch to the rear and then two screws which secure the catch plate inside the door. view full answer...
Yes, you do have it right concerning the Solera 20' White Fade RV Awning Roller and Fabric # LCV000211523.
It comes with the roller, and is able to be used as a manual awning as you would then attach it to your rail and arms, such as the Solera Universal Awning Support Arms - White # LC434728 or Black # LC434727.
I have added a link below to a video review for you to check out as well if you'd like to take a look. view full answer...
For your 2021 Heartland Trail Runner Travel Trailer I recommend the Furrion Vision S Wireless RV Observation Camera System Item # FCE48TASL-05. This kit comes with the the rear camera, two side cameras, and a 7" LCD color monitor. All cameras have LED lights for visibility at night. The rear camera has a built-in microphone and the system has built in motion detection. The system is a wireless system and does not require a wire connection from cameras to the monitor. Each camera simply... view full answer...
All the parts you need to install the hitch is included with the Curt Hitch receiver # 13551. This hitch receiver is for a Ford Flex with dual exhaust. You will need the Curt T-Connector Wiring Harness to allow you to hook up to your camper. The wiring that I recommend for your 2011 Ford Flex is # C55774. This gives you the option of using either a 4-pole connector or a 7-Pole connector. You also need a ball mount like # C74WR for an 8000-lb capacity or the # WSFH2-2 for a 10,000-lb capacity... view full answer...
Yes. The Furrion RV Cooktop - Propane - Triple Burner - Stainless Steel # FGH4ZSASS comes with a built in LP regulator. As for connecting to the propane source, this cooktop does come with a hose designed to connect to an RV propane kitchen pipe. If you are going to connect it directly to a propane tank then you'll also need another regulator on that hose according to new regulations from the RVIA. If you've got a propane tank with a Type 1 fitting you could use any of these hoses to connect... view full answer...
There isn't a way to get the Slide topper without the rail, so you would need to get the full kit:
- Solera RV Slide-Out Awning - 13'1" Wide # LCV000168109
This will fit slides that have a flange-to-flange measurement of 152" to 157" wide. I did want to mention, just to cover all the bases, that if you were referring to your trailer coming with the Solera pre-installed brackets, and not the rail, you would still need the full awning kit, but you would also need the Solera Slide Topper... view full answer...
The only other part that comes in the package of your TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear # TLR3501 apart from the parts you mentioned is the metal pin/clip that attaches the tie-down shank into the receiver shank. I went ahead and attached a video that shows all of the parts included.
If this is not the part you are inquiring about, I would be happy to assist you if you respond to this answer with a photo of the extra part. view full answer...
Curt RV Bumper 2" Trailer Hitch Receiver Item # E-100 comes with 2 HFN 1213 hex flange nuts for the two 1/2 - 13 x 5-1/2 carriage bolts also included with the hitch. view full answer...
Part # TLF2022 consists of 2 TorkLift front tie-down inserts, frame brackets, and the necessary mounting hardware. The rear kit only for the 2017 Ford F-350 is part # TLF3008. Both of these are a confirmed fit for the 2017 F-350 with 6-3/4 Foot Bed, without board or step underneath truck bed and with a factory installed hitch. These will not fit trucks with factory flip-out steps that are mounted under the bed. view full answer...
Yes, the Rhino-Rack part # Y02-480B is a complete adjustable track-mount roof rack system that includes a pair of tracks, four leg assemblies, two aero-style crossbars and locks. This is intended primarily for applications on camper shells, hard tonneau covers, or hardtop resin roofs as found on some RVs.
This rack setup could also be installed on the roof of a vehicle such as your 2012 Chevrolet Silverado but we have other custom roof rack options that will not require drilling into the... view full answer...
The Swagman Traveler XC2 Bike Rack for 2 Bikes - 2" Hitches or RV Bumpers - Frame Mount Item # S64663 comes with an anti-rattle hitch pin but if you want a locking one you'll need the Locking Anti-Rattle, Threaded Hitch Pin for Swagman 2" Hitch Racks Item # S64027 view full answer...
Yes it does, the part # ETBC6 when installed will give your 2008 Toyota Rav4 a fully functional 6-way and 4-way so it should work perfectly for you.
I attached a set of installation instructions for you to check out. view full answer...
The etrailer Hitch with 2" receiver # e98844 you mentioned is a great choice to start off, and this hitch comes with a durable powder coat that will help ensure that it stands up to dings and nicks that might otherwise lead to rust. In addition to a trailer hitch, you'll need a wiring harness, ball mount, hitch ball, hitch pin, clip and potentially a brake controller if the trailer you'll be towing has brakes. For the trailer wiring, I recommend using the Tekonsha # 118449 if you'll only... view full answer...
If you don't want the variety of hitch pin locks that are found in the tow bar lock kit # e86ZR, we also have them available individually so that you can pick and choose what you want.
You can order 3 pcs of the etrailer Trailer Hitch Receiver Lock for 2" Hitches -Chrome # e98880. Just select "Keyed Alike" and make sure all three are in the same order and we will make sure the lock cores match before we ship them out to you. You can do this with any of our etrailer locks like the # e98882... view full answer...
The Curt Class IV 2 Inch Hitch, part # 14301, will include all of the mounting hardware. I am including a link to the installation instructions of the Curt hitch.
If you will be towing with this hitch on your 2007 Chevrolet Silverado New Body you will also need to purchase the following items.
Draw-Tite Ball Mount, part # 40331
Hidden Hitch Pin And Clip, part # PC3
Curt 2 Inch Hitch Ball, part # A-90, or Tow Ready 2-5/16 Inch Hitch Ball, part # 19286
Pollak Twist-in, 7-Pole, RV-Style... view full answer...
Go To Results